Dromida MT4.18 Assembly Guide Manual do Utilizador descarregar pdf

HELPFUL HINTS

✔ Avoid working over a deep pile carpet. If you drop a small part or screw,

it may be difﬁ cult to ﬁ nd.

✔ Place a mat or towel over your work area. This will prevent parts from rolling off and will protect the work surface.

✔ Avoid running the car in cold weather. The plastic and metal parts can become brittle at low temperatures. In addition, grease and

oil become thick, causing premature wear and poor performance.

MAINTENANCE

BEFORE EACH RUN

✔ IMPORTANT:

Check to make sure that all

screws are tight. Check that the servo

saver screw is fully tightened to ensure

that your Dromida MT4.18 tracks straight.

✔ Always check the condition of your

radio system batteries and replace if

necessary.

✔ Check to make sure that all of the

moving parts of the Dromida MT4.18

move freely and do not bind.

✔ Turn on the radio and make sure the

servo moves easily and in the proper

direction.

✔ Check for any broken or damaged

parts. Replace them before running the

Dromida MT4.18. Running the Dromida

MT4.18 with broken or damaged parts

could damage additional parts.

✔ Check to make sure that all wires are

properly connected.

AFTER EACH RUN

✔ Clean any debris from the chassis and

moving parts.

✔ Check for any broken or damaged parts.

Replace them before the next run.

✔ Disconnect and remove the battery

from the chassis.

AFTER EVERY 10 RUNS

✔ Check to make sure that the bearings

are free of dirt and debris, and roll

smoothly.

✔ Check the shocks for oil leakage.

✔ Check the tires to make sure they are

still properly glued to the rims.

ASSEMBLY AND MAINTENANCE GUIDE

HARDWARE CHART

2x10MM FLAT HEAD SCREW

2x14MM FLAT HEAD SCREW

2.5x8MM FLAT HEAD SCREW

2.5x8MM SOCKET HEAD SCREW

2.5x14MM SOCKET HEAD CAP SCREW

3x6MM SOCKET HEAD SCREW

2x8MM ROUND HEAD

SHOULDER SCREW

3x3MM SET SCREW

3MM LOCK NUT

1.5x6MM E-CLIP

2.6x5MM WASHER

3x6MM WASHER

BODY CLIP

(

SMALL

)

2x6MM SELF-TAPPING

ROUND HEAD SCREW

2x4MM ROUND HEAD SCREW

2x8MM FLAT HEAD SCREW

2x8MM ROUND HEAD SCREW

2x10MM ROUND HEAD SCREW

6x10MM BALL BEARING

8x12MM BALL BEARING

ACTUAL SIZE

(

WHEN PRINTED AT 100%

)

™

1 2 3 4 5 6 7 8 9

Resumo do Conteúdo

Página 1

HELPFUL HINTS ✔ Avoid working over a deep pile carpet. If you drop a small part or screw,it may be difﬁ cult to ﬁ nd.✔ Place a mat or towel over you

Página 2 - 2. DIFFERENTIALS TO CHASSIS

313332333032GGBGGB34GREASEGREASEGREASEGREASENOTE DIRECTIONNOTE DIRECTION221HHHH1. DIFFERENTIAL ASSEMBLY 2. DIFFERENTIALS TO CHASSIS

Página 3 - 4. CENTER SHAFT

3. STEERING ASSEMBLY 4. CENTER SHAFT 1845184040444046PPDO NOT OVERTIGHTEN(WILL CAUSE BINDING)DO NOT OVERTIGHTEN(WILL CAUSE BINDING)28292728ABAGREASEGR

Página 4 - 6. MOTOR MOUNT

5. SHOCK TOWERS 6. MOTOR MOUNT 738711240340404011GGEEVVEEEEEENOTE DIFFERENCENOTE DIFFERENCENTNKQKTEEEEEE392642524THREADLOCKTHREADLOCK

Página 5 - 8. REAR SUSPENSION

7. FRONT SUSPENSION 8. REAR SUSPENSION 41DO NOT OVERTIGHTEN42414338154036353717BBBEARINGS FULLY SEATEDDO NOT OVERTIGHTEN4091440LLCH1318HACTUAL SIZE11.

Página 6 - 9. RADIO BOX

GGG9. RADIO BOX 10. SHOCK ASSEMBLY 564050515249474748XSFXSCREW MUST BE SNUGCENTER SERVO FIRST7.5MMACTUAL SIZESHOCK OILSHOCK OILSHOCK OILSHOCK OIL58556

Página 7 - 12. FRONT SHOCK INSTALLATION

11. REAR SHOCK INSTALLATION 12. FRONT SHOCK INSTALLATION 53SM53SM

Página 8 - 14. WHEELS

13. BUMPER 14. WHEELS 1919EEEE7070RR7273

Página 9 - TUNING GUIDE

TUNING GUIDE When tuning the Dromida MT4.18 make sure that you have equal lengths from one side to the other on the shocks and upper rods. Also, make